1. The output temperature range has a large span, which can meet the different requirements of Yin mold and Yang mold temperature machine in the injection process at the same time, overcoming the discomfort of mold temperature control caused by the change of environmental temperature caused by mold temperature machine or chiller or a combination of both.

2. The pipeline of the ice water circulation system of the chiller is made of PP-R environment-friendly material with a service life of 50 years, which can effectively prevent the generation of water rust from the source and reduce the pollution to the customer’s equipment and the blockage of waterways. A unique and effective combination of one set of refrigeration and two sets of heating can output water lower than or higher than the ambient temperature in the same heat transfer media output pipeline, realizing automatic switching.

3. No matter at which point the control temperature is set, the heat transfer media with a certain flow rate can be output in the output pipeline, so that the mold temperature can be accurately and effectively controlled no matter it is set below or above the ambient temperature.

1. The oil tank is designed for semi-closed circulation and independent oil tank to reduce oxidation caused by contact between hot oil and air. Increase the heat medium reserves in well, make it difficult to stop oil, the cooler adopts the design of sealed immersion cooler, the cooling effect is immediate, efficient and safe, easy to maintain, pump within 200 degrees using gear pump, improve the pressure of heat medium oil; The high temperature oil mold temperature machine is changed to the heat media boiler special water-free cooling but heat media pump, which can withstand temperature of 350°C, with large flow and good heat transfer effect.

2. Equipped with the computer control panel imported from Taiwan, the 5LCD screen can switch between Chinese and English, with high temperature control precision, stability and reliability, and equipped with 486 output terminals, truly realizing the man-machine interface. , basically have boot automatically exhaust, delay shutdown automatically cool (similar to the car radiator cooling fan in the function), to prevent electric heating air burn, let the machine service life is longer, the whole system more secure, complete series use bold stainless steel seamless tube, increase the heating surface area, reduce the current density, let the heat conduction oil is not easy to knot carbon metamorphism, prolong service life, and at the same time, adopt the demountable type electric heating design, change is also very convenient.

3. The maximum temperature control is 180°C and 280°C respectively.

1. Water mold temperature machine as a media has its advantages: high heat conduction efficiency, less pollution, easy access to water resources, temperature control range up to 160℃; The advantages of oil mold temperature machine is a large range of temperature control, thermal stability, but the need for media cost, grease, the latest model, temperature control range has reached 320℃, with a compact structure, the rise and fall temperature speed, accurate temperature control characteristics

。

1. In the process of injection molding, mold temperature has a direct impact on the filling and shaping of plastic parts, and ultimately also affects production efficiency and quality.

2. Make all positions of the mold have the same temperature as far as possible, so that the acid and heat rate and degree of the mold inside the cavity are close to the same, to ensure the quality of the parts, avoid or reduce the occurrence of internal stress resulting in the decline of the mechanical strength of the parts.

3. Shorten production cycle and strengthen production efficiency. If the mold is left to work at a constant high temperature, the time it takes for the parts to cool in the mold to fully solidify increases, prolongs the opening time, and consequently increases the production cycle and production cost.

4. Effectively cool the cavity. The so-called effective cooling, is under the premise of smooth mold filling, will be in the molten state of 100-300℃ into a solid near room temperature when the heat transferred to the mold as quickly as possible to remove all the parts quickly from the cavity surface. If the heat cannot be removed effectively during the production process, the mold temperature will increase gradually, which may lead to many defects such as flapping, retracting and retracting, ejecting deformation and large deformation after cooling.

1. The laser chiller cools the laser generator of the laser equipment.

2. In the long running process of laser equipment, the laser generator will constantly generate high temperature, which will affect the normal operation of the laser generator. Water cooling is needed to take away the heat, and the water chiller controls the temperature of the laser generator, so that the laser generator can keep working normally for a long time.

1. A special controller designed with a single chip microprocessor.

2. The combination of P.. D Temperature control technology makes temperature control more precise.

3. Simple operation, more complete function.

4. On-line function (RS485), MODBUS communication protocol, easy to connect with various man-machine interfaces, PLC and laptop.

1. Welding robots are divided into spot welding, arc welding, projection welding and laser welding. Although the heating of arc welding equipment is generally low, the equipment itself has a small air-cooled chiller for spot welding. Convex welding and laser welding have large heating capacity, which require higher cooling of welding tongs, and the high temperature is easy to form virtual welding. The welding strength cannot meet the requirements, and the temperature is too high, so the lighting machine will alarm and automatically stop, so another chiller is needed.

1. Air-cooled chiller is using 売 tube evaporator water heat exchange with the refrigerant, refrigerant system in absorbs the heat load of the water, the water after cold water cooling, through the role of the compressor to the finned heat condenser, again by the cooling fan is lost to the outside world in the air.

2. Water cooled chiller is using 売 tube evaporator water heat exchange with the refrigerant, refrigerant system in the absorption of heat load in the water, the water cooling after cold water, through the role of the compressor will heat to shell and tube condenser, the refrigerant and water to heat exchange, after the water absorption heat through heat pipe will out of the outside of the cooling tower is lost.